[BioC] two color arrays normalization

[Naomi Altman]

Hi Giusy,
Move the minus signs from the first design matrix to the 2nd and I 
think it will work fine.

--Naomi

At 06:07 PM 2/17/2009, Giusy Della Gatta wrote:
>Hi Naomi,
>
>I performed the analysis of my micorarrays,but still I don't manage 
>to revert the channels!
>My experiment consisted into infect cells with an adenovirus: an emty one
>and an adenovirus expressing for a specific protein.  Then I
>treated the same cells with a specific drug or simply with the vehicle (DMSO).
>I have 6 microarrays: 3 controls DMSO0-treated and 3 samples drug-treated.
>In each microarray the green channel is expressing the levels of 
>infected and treated
>cells while the red channel are not infected cells. For all the experiments
>I have the same RED CHANNEL reference.
>I composed the target file as follows:
>
>Filename        Cy3     Cy5
>Control_1b.txt  ctrl    ref
>Control_2b.txt  ctrl    ref
>Control_3b.txt  ctrl    ref
>dexa_dbz_lt_1.txt       treat   ref
>dexa_dbz_lt_2.txt       treat   ref
>dexa_dbz_lt_3.txt       treat   ref
>
>and the I used the following script:
>
> >targets=readTargets("target_frame_ltbarc_pgedit.giusy")
> >RG<-read.maimages(targets$FileName, source="agilent", ext="txt")
> >MA<-MA.RG(RG, bc.method="normexp")
> >MA<-normalizeWithinArrays(RG, method="loess")
> >design <- modelMatrix(targets, ref="ref")
> > design
>  ctrl treat
>[1,]   -1     0
>[2,]   -1     0
>[3,]   -1     0
>[4,]    0    -1
>[5,]    0    -1
>[6,]    0    -1
> >fit<-lmFit(MA,design)
> >cont.matrix<-cbind("ctrl-ref"=c(1,0), "treat-ref"=c(0,1))
> >cont.matrix
>      ctrl-ref treat-ref
>[1,]        1         0
>[2,]        0         1
>
> >fit2<-contrasts.fit(fit, cont.matrix)
> >d1 <- ebayes(fit2)
> >toptable(fit2,adjust="fdr")
>
>I don't know if I am still omitting
>something, because I have the positive
>controls of this experiment  that
>are going exactly in the opposite way!!
>
>May you can help me?
>
>Thank you in advance!
>Giusy
>
>
>-----Original Message-----
>From: Naomi Altman [mailto:naomi at stat.psu.edu]
>Sent: Mon 2/9/2009 9:56 PM
>To: Giusy Della Gatta; bioconductor at stat.math.ethz.ch
>Subject: Re: [BioC] two color arrays normalization
>
>If there is no dye-swap, then what do you mean by "swapping of the colors"?
>
>--Naomi
>
>At 07:56 PM 2/9/2009, Giusy Della Gatta wrote:
>
> >Hi everybody,
> >
> >I am analyzing two color Agilent microarrays
> >by using LIMMA package.
> >In my specific case the red channel is representing
> >"the reference" while the green channel is "the treatment".
> >Is it enough to use the Target File composition to specify the name
> >of  the samples
> >and their corrispondet channels?  Or I have to use other specific commands
> >to specify the "swapping" of the colors?
> >
> >Thank you in advance!
> >Regards
> >Giusy
> >
> >_______________________________________________
> >Bioconductor mailing list
> >Bioconductor at stat.math.ethz.ch
> >https://stat.ethz.ch/mailman/listinfo/bioconductor
> >Search the archives:
> >http://news.gmane.org/gmane.science.biology.informatics.conductor
>
>Naomi S. Altman                                814-865-3791 (voice)
>Associate Professor
>Dept. of Statistics                              814-863-7114 (fax)
>Penn State University                         814-865-1348 (Statistics)
>University Park, PA 16802-2111

Naomi S. Altman                                814-865-3791 (voice)
Associate Professor
Dept. of Statistics                              814-863-7114 (fax)
Penn State University                         814-865-1348 (Statistics)
University Park, PA 16802-2111